Brand: Aplicaciones Tecnológicas
Reference: AT-9071
IGA TEST COMPACT series protectors cut the line when they detect a permanent overvoltage (eg neutral faults), thus protecting downstream equipment.
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
The IGA TEST COMPACT series protectors cut the line when
detect a permanent overvoltage (for example, neutral faults),
thus protecting the equipment installed downstream.
To reset the circuit breaker, it is first necessary to reset
the protection coil, for which the RESET button is used.
In addition, the IGA TEST COMPACT protectors also act by detecting
a transient overvoltage by diverting the current to ground and reducing the
voltage at a level not harmful to the connected equipment.
Tested and certified as a type 2 protector in official laboratories and
independent according to standard UNE-EN 61643-11 and GUÍA-BT-23 of the REBT.
It has a thermodynamic device for disconnection from the electrical network
in case of degradation and surge warning system
transitory. When the buzzer glows green, the protector is on
good condition. If not, replace.
The integrated circuit breaker is available for the currents
typical ratings: 6, 10, 16, 20, 25, 32, 40, 50 and 63 A.
> INSTALLATION
It is installed in series with the low voltage line, between the switch
power control (ICP) and differential switch (ID), connecting it
to Earth.
The installation must be done without tension in the line.
This protector is composed of a protection coil against
permanent overvoltages, which includes a protector against
transient overvoltages, associated with an automatic switch.
Reference: AT-9071 AT-9072 AT-9073 AT-9074 AT-9075
Nominal current: 25 A 32 A 40 A 50 A 63 A
Rated voltage: Un 230 VAC
Maximum overvoltage: 400 VAC
Actuation voltage: Ua 265 - 280 VAC
Actuation time: @ 275 V → 8 - 10 s / @ 400 V → 0.1 - 0.2 s
Cutting capacity: 6 kA
Type of tests according to
UNE- EN 61643-11: Type 2
Rated current
discharge: I
n 5 kA
Maximum current: I
max 15 kA
Protection level: Up 1.5 kV
Dimensions: 51 x 81 x 65 mm (3 modules DIN43880)
Cable range: Minimum / maximum section: 1.5 / 16 mm2
cuando colocas el protector permanente y transitorio , se anula el automático general , y de cuantos amperios seria para la vivienda de 230v. con una potencia de 4000w.
Buenos días, por lo que veo hasta 4,6 KW el IGA es de 20A. El iGA no deja de ser un magnetotérmico asociado a las bobinas que lo hacen saltar por las sobretensiones.
bon produit installation facile
Fácil de instalar, aunque podría llevar a la confusión ya que la entradas es por abajo si no se tiene el manual, por lo demás el tiempo lo dirá, por ahora no hay tormenta eléctrica y fallos en la red
Primera experiencia con Voltiks y satisfactoria. Buenas atención y plazo correcto. El sobretensiones instalado sin problemas.
How do reviews and ratings work?
The opinions and ratings of the products are mostly made by registered customers who have purchased the product. These reviews appear with a "verified purchase" mark. In any other case this mark does not appear. The product rating, out of 5 stars, is calculated as the average of all published ratings for the product. To ensure the information is useful for other customers, reviews and ratings, whether positive or negative, are published after prior approval.